Chevy Astro Camper Van Build: Solar Panels

Chevy Astro Camper Van Build Phase 9: Solar Panel Installation

Installing two 100w solar panels

Tools & Materials

Materials

2 100W Solar Panels
Solar Panel Wires Roof Entry Port
Renogy 20FT 10AWG Solar Extension Cables
Solar Panel Y Branch Connectors
Spax Construction Screws
Adjustable Rope Hangers
Aluminum Tubing & Connectors
Sheet Metal Screws
Rivet Nut Set
Hinges
16 Gauge Sheet Metal Plate
Loctite Threadlocker 242
Angle Aluminum
3M VHB Tape
Heavy Duty Waterproof Rubberized Roof Tape
Loctite PL Max Construction Adhesive
Sikaflex 715
Metal Cutting Diamond Blade for Angle Grinder
Renogy 20a Inline Fuse

Tools

Dewalt Cordless Impact Driver
1/4ā€³ Drive Quick Release Bit Extension
Craftsman 3/8 Drive Drill
Dewalt Compound Miter Saw
Rivet Nut Tool
Center Punch Set
Craftsman Socket Set
Dewalt Angle Grinder
File Set
C Clamps
Countersink Bit Set

Ā 

Video ā€“ Chevy Astro Camper Van Build: Solar Panels

Project Overview: Solar Panel Installation

Mounting solar panels could have been a quick and easy job, but No out-of-the-box solution appealed to me. I did it the hard way and custom fabā€™d everything from the frame to the mounting brackets. And, I got the wild idea to mount the brackets for he panel with tape instead of drilling through the roof. Sounds like a crazy idea, but after a year on the road, itā€™s been holdings strong. Maybe Iā€™m not crazy.

Iā€™m going to build a mounting frame for the two solar panels, so I can mount them and move them together as one piece. Iā€™ll using aluminum tubing for this. Then, the idea is to mount the back side of the aluminum frame to the roof rack using hinges, and then make my own metal brackets for the front that will get taped down to the roof of the van using very strong adhesive tapes, and a very large surface area. There are other adhesive solar panel mounting systems on the market, but they consist of multiple ā€œclipsā€ that stick to the roof with the same kind of adhesive tape Iā€™m using. Iā€™ll just use two huge brackets with a surface area 20x larger. It should definitely work.

Building A Mounting Frame For The Solar Panels

Just need to cut the frame to size

Cutting the aluminum tubing

Frame cut to size. The solar panels will go hereā€¦

I bought 1ā€³ aluminum tubing and connectors from a company called EZ Tube, and building the frame is pretty straight forward. The top photo above shows the solar panels sitting inside the frame, which is too big. So, All I need to do here is cut the aluminum to the right size to fit around the panels. I use a hacksaw to make my cuts, and a file to clean up the edges so the plastic connector pieces slide in smoothly.

Sheet metal screws

Screwing the solar panels into the frame

Solar panels and frame are now one

Add Hinges To Roof Rack

Drilling holes for the hinges

Installing the hinges

Let me be the fist to tell you, this is NOT a ā€œnormalā€ way to mount solar panels. Iā€™m using hinges to attach one side of the solar panel frame to the roof rack. Iā€™m using hinges for a few reasons. First and foremost, I would need one really long bolt to go through the aluminum tubing and the roof rack, not to mention the fact that it would be impossible to have access to the nut or bolt on the underside of the solar panels to actually mount the thing. So, the hinges are mostly for ease of installation. One side of the hinge is mounted to the roof rack. The hinge flips up and provides easy access to bolt the other side of the hinge to the solar panel frame.

The other bonus about using the hinges is that my solar panels could now, theoretically, be adjustable, allowing me to tilt them up to follow the angle of the sun. This is, of course, dependent on how I go about mounting the solar panel frame in the front, as that would need to be easily removable in order for this idea to really be feasible out in the backcountry.

Iā€™m using Loctite Threadlocker 242 on these bolts, as I want to make sure none of this stuff comes loose while driving over rough roads, etc.

Install Rivet Nuts In Solar Panel Frame

Drilling holes for the rivet nuts

Check out the name of my Rivet Nut toolā€¦ ASTRO! It was meant to be

Next, Iā€™ll need to fasten the hinges to the solar panels. I drilled some holes in the solar panel frame and mounted a few rivet nuts. This will give me a female thread to thread into when itā€™s time to mount the hinges to the frame.

Run Solar Panel Wires Through Roof

Solar Panel wires will get routed through the roof here

Before I mount the solar panel frame to the roof rack, Iā€™ll want to run my solar panel wires up here through the roof while I have unrestricted access. I drill holes through the roof and use rubber grommets to line the holes with. This will protect the wires from the sharp edges of the metal.

About to lay down the housing on the VHB tape

The solar panel wires entry housing thing. Great product

Next, I use this Solar Panel Wire Roof Entry Port thing. Itā€™s a little plastic housing that fits over the holes I cut through the roof for the solar panel wires, and basically makes the whole thing waterproof. I run my wires up through the roof, through the entry port thing and out of the little holes on the housing. I can then twist the little connector pieces to tighten up the seal and make the connection waterproof. I use double-sided 3M VHB tape to connect the housing to the roof. I set the housing on the tape and it forms a rgeat bond. I trim up the excess tape outside of the edges of the housing, and lay some Sikaflex-715 down over the edges of the housing for a fully waterproof seal. I hope.

Attach Solar Panel Frame To Roof Rack Hinges

Lining up the panels with the hinges

Screwing down the solar panels to the hinge

Now itā€™s time to connect the solar panels to the roof rack. At this point, itā€™s just a matter of lining up the holes of the hinges with the rivet nuts on the solar panel frame. As with the other bolts from the hinges to the roof rack, Iā€™m using Loctite Threadlocker 242.

Making Metal Brackets For Mounting Front of Solar Panel Frame

Cutting the sheet metal into 4ā€³x8ā€³ pieces

Tracing out the next cut

Next, I start the most complicated part of the solar panel mounting system, and the part that has me a little nervous; the mounting brackets for the front of the solar panels. Since the panels are well secured to the roof rack in the rear, I just need to think about securing them in the front. For some reason, I had it in my mind that I was NOT going to drill through my roof to mount my solar panels. I donā€™t know why, since Iā€™ve drilled through the roof already for the Maxx Fan Installation and running the solar panel wires through. Either way, I was fixated on coming up with a no-drill solution. I found some mounting brackets online that fit around the edges of he panels, but they are supposed to be used when mounting to a flat roof, not a curved roof like mine. None of the products on the market, that I could find, seemed to jump out at me as a good fit for me and my van. So, I decided to make my own mounting brackets for the front.

I settled on 16 gauge sheet metal to make the bottom side of my mounting bracket. A large surface area is key to my plan here. Iā€™m going with a size of roughly 4ā€³x8ā€³. So, Iā€™ll need to cut down this piece of sheet metal to size. First, I tried using my miter saw with a metal cutting blade. I was getting nowhere. I eventually switched to my angle grinder and aĀ Metal Cutting Diamond Blade. This did the trick and I was able to make the cut. Then, I used the piece I just cut to trace out another piece for the second bracket.

First view at the concept of the brackets

Next, I take my 4ā€³x8ā€³ sheet metal squares outside and place them under my solar panel frame to get an idea of where Iā€™ll ultimately put them. I cut a piece of angle aluminum about 3 inches wide and place that on top of my 16 gauge sheet metal rectangles. Now, you can see the bracket idea coming together.

Tracing out a line where the angle aluminum will sit on the sheet metal

Used a countersink bit to allow my screw heads to fit flush

Next, I clamp the angle aluminum to the sheet metal and trace out a line where it will sit. I have pilot holes drilled through the angle aluminum, which allow me to mark the sheet metal underneath. Then, I drill holes through the sheet metal. On the bottom side of the plate, I use a countersinking bit to drill out a conical shaped divot into the sheet metal. This allows the screw heads to sit flush with the sheet metal plate. This is important, because this bottom side will be mounted to the van roof.

The bracket is complete

Another view of the completed solar panel mounting bracket

Now itā€™s time to attach the angle aluminum to the sheet metal. Iā€™ll run a screw through the bottom of the sheet metal and up through the angle aluminum thatā€™s sitting on top. I use a washer, nut and Loctite Threadlocker 242Ā to fasten the angle aluminum to the sheet metal.

Adding VHB tape to the bottom of the bracket

Finally, I add 3M VHB tape to the bottom of the brackets. When itā€™s time to attach the brackets to the roof, Iā€™ll also be using construction adhesive in between the strips of tape in an attempt to achieve the strongest possible bond.

Attach Solar Panel Wires To Solar Panels

The little black things in the middle of the roof are a thick rubberized mat material. Iā€™m taping these to the roof with VHB tape to give the panels some support in the center and to prevent sagging

Before I mount these solar panels in place, Iā€™ll finish attaching the wires that I ran from inside of the van to the panels. These go to my DC to DC Charger, which I will be installing in the near future. For now, these connections are easy, they just plug in to each other. Iā€™m using a Renogy 20a Inline Fuse here in between the Renogy 20FT 10AWG Solar Extension CablesĀ and theĀ Solar Panel Y Branch Connectors.

Fasten Metal Brackets to Solar Panel Frame

Drilling holes for the rivet nuts

Installing the rivet nuts

Fastening the brackets to the frame

Next, Iā€™ll mount the brackets to the solar panel frame. Iā€™ll need to drill some hoes in the frame and install some rivet nuts. Once thatā€™s done, I screw the brackets into the rivet nuts on the solar panel frame.

Secure Metal Bracket (Underside) To Roof With Tape & Adhesives

Last look at the underside of the panels before they are mounted to the roof

Adding a bead of construction adhesive

Now Iā€™ll mount the brackets to the roof. Itā€™s time to take off the VHB tape and add a bead of PL Max construction adhesive to the strips I left in between the tape. I figure, this will add a different type of bond to the mix, and also provide a waterproof layer around the VHB tape, perhaps protecting it over time. Before setting the bracket down on the roof, Iā€™ll clean it up again one last time with rubbing alcohol.

This is an important step in ensuring the strongest bond possible

With the down on the down on the roof, I move the van into the garage and sue some 4Ɨ4ā€™s to press down on the brackets, providing constant pressure while the construction adhesive cures. Iā€™ll let this sit overnight like this before coming back to it.

Secure Metal Bracket (Top Side) To Roof With Tape & Adhesives

Putting VHB tape on top of the brackets

The last step is an important one. While itā€™s possible that the VHB tape and construction adhesive from the previous step might be enough to secure these solar panels at highway speeds, there is no way I would chance that. There is still much more I can do here to make sure these brackets are secured to the roof firmly and that itā€™s going to be safe to drive. Iā€™ll be adding a few more layers of tape over the brackets now. Iā€™ll be trying to cover a large surface area, which is key to creating a a lot of holding power.

Firstly, I add a few more layers of 3M VHB tape. First I go around the perimeter of the bracket, covering the edges, then I run longer strips across the top. I can already feel how strong this is.

Laying the heavy duty rubberized waterproof tape over the vhb tape

The heavy duty rubberized tape is down and the mounting brackets are installed

Lastly, I add a few layers of this Heavy Duty Waterproof Rubberized Roof Tape over the VHB tape. This stuff is very thick and very strong. Itā€™s used for patching roof leaks on RVs, and similar heavy duty repairs. I make sure to overlap all of the VHB tape I have applied, and run a few layers over each other.

Now, all I have to do is set the solar panels down and screw the frame to the bracket. Iā€™ll use Loctite Threadlocker 242 for this. Solar panels, done.

One more thing: If I can figure out a ā€œquick connectā€ system for attaching the solar panels to the brackets, instead of screws with Threadlocker, I might be more inclined to disconnect the panels from the front brackets and adjust the angle of the panels using the hinges in the rear to follow the sun during extended stays at backcountry campsites. Because I spend most of my time in the West, where itā€™s always sunny, I donā€™t even need to bother with adjusting the angle of the panels because there is already so many hours a day of full sunlight. However, I might be more tempted to pursue this quick connect idea if I were going to be spending more time in places that had less sunlight, where one needs to maximize any any all sunlight available.

**Update:

Itā€™s been 15 months now and 20k miles of driving, and I have had ZERO issues with my solar panel mounting system. Iā€™ve never had the brackets come off or come loose, never had a close call or anything. Nothing is peeling or deteriorating. I have driven the van up to 85 MPH and the brackets have held strong. This system WORKS!

Ā 

Previous Van Build Project: 8 ā€“ Lithium Battery | DIY Stealth Camper Van Build IndexĀ | Next Van Build Project: 10 ā€“ Electrical Wiring